View unanswered posts | View active topics It is currently Fri Mar 29, 2024 8:55 am



Reply to topic  [ 36 posts ]  Go to page Previous  1, 2
G150 Rebuild Kits? 
Author Message
User avatar

Joined: Sun Oct 05, 2008 10:21 pm
Posts: 528
Location: Darwin NT
Car(s): Isuzu Bellett, VG Commodore Ute, Custom Chopper
Reply with quote
Yes I am absolutely going to remove welch plugs for an acid bath (it has been sitting in the back of my shed for 10 years I think - I remember doing the same for the motor in Stinky now.

It is not a rant when it is advice CQ - all good. I am very open to advice - that is why I post these things so Bellett.net can give me heads up!! I thank you all!


Thanks Dave for the info on the Cam Bearings - will let you know how I go.


Cheers,
Neil


Wed Nov 06, 2013 8:58 pm
Profile WWW
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
gt orphanage wrote:
just make sure you can get cam bearings before you go acid bathing it :!: they are a little hard to find ;)


has anybody solved this problem of cam bearings ? I had same issue way back in 90's on the GT engine rebuild.

_________________
'72 PR60 Sport


Wed Nov 06, 2013 9:32 pm
Profile WWW

Joined: Tue Mar 24, 2009 11:52 am
Posts: 843
Location: Sunshine Coast QLD
Car(s): PR95 PR20 WASP SWB NH Pajero Superchrged NT Pajero BF SR6 Falcon
Reply with quote
Somewhere in the old memory bank I recall that 1200 Suzuki Motor cycle bearings were being modified to fit. :roll: :?:


Wed Nov 06, 2013 11:22 pm
Profile

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
I think you will find that Suzuki mod was twin cam.


Thu Nov 07, 2013 12:39 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
does anybody have the dimensions of the bearings (Bellett that is)

_________________
'72 PR60 Sport


Thu Nov 07, 2013 1:01 am
Profile WWW
User avatar

Joined: Sun Oct 05, 2008 10:21 pm
Posts: 528
Location: Darwin NT
Car(s): Isuzu Bellett, VG Commodore Ute, Custom Chopper
Reply with quote
Hello Glenn,

I found this info on camshaft bearings this morning:

Camshaft Bearing Set 3C6127
Oversize STD
Brand ACL
Manufacturer ACL
Camshaft Bearing (c) 6127
- 1,2,3
OE Part Number 1 5-11611-002
Manufacturer ACL
Min Std Shaft Size 1.7707in / 44.975mm
Max Std Shaft Size 1.7707in / 44.975mm
Min Std Tunnel Size 1.8902in / 48.01mm
Max Std Tunnel Size 1.8909in / 48.03mm
Max Wall At Crown 0.0591in / 1.5mm
Max Overall Length 1.0000in / 25.4mm
Semi-finished N
Min Vertical Oil Clearance 0.0014in / 0.035mm
Max Vertical Oil Clearance 0.0037in / 0.095mm
Material F23


MAIN BEARINGS:
Main Bearing Set 5M2817
Oversize STD, .25, .50, .75, 1.00, 1.25, 1.50
Brand ACL Duraglide
Manufacturer ACL
Main Bearing (c) 2817
- 1,3,5
Half Type Identical Halves
OE Part Number 1 9-11510-609
OE Part Number 2 9-11510-141
Manufacturer ACL
Min Std Shaft Size 2.2016in / 55.92mm
Max Std Shaft Size 2.2022in / 55.935mm
Min Std Tunnel Size 2.3220in / 58.98mm
Max Std Tunnel Size 2.3228in / 59mm
Max Wall At Crown 0.0596in / 1.513mm
Max Overall Length 1.2650in / 32.13mm
Min Vertical Oil Clearance 0.0007in / 0.019mm
Max Vertical Oil Clearance 0.0031in / 0.08mm
Material F780
Main Bearing (c) 2818
- 2,4
Half Type Identical Halves
Manufacturer ACL
Min Std Shaft Size 2.2016in / 55.92mm
Max Std Shaft Size 2.2022in / 55.935mm
Min Std Tunnel Size 2.3220in / 58.98mm
Max Std Tunnel Size 2.3228in / 59mm
Max Wall At Crown 0.0596in / 1.513mm
Max Overall Length 0.8299in / 21.08mm
Min Vertical Oil Clearance 0.0007in / 0.019mm
Max Vertical Oil Clearance 0.0031in / 0.08mm
Material F780

Hope that helps mate.
Neil


Thu Nov 07, 2013 1:06 am
Profile WWW

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
I have a new set here a forum member helped me get :!: it's up to that forum member to say if he can get more as I think the supply is low if not gone.


Thu Nov 07, 2013 1:09 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
Thanks Neil

I don't need any now, but the info could help soembody out maybe. I wonder if the SOHC and DOHC lay shaft uses the same bearings.... i would imagine so.

_________________
'72 PR60 Sport


Thu Nov 07, 2013 4:02 am
Profile WWW

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
last time I checked acl no longer had stock and were not making any :?: Maybe a group buy I would get a couple more sets.


Thu Nov 07, 2013 5:14 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
gt orphanage wrote:
last time I checked acl no longer had stock and were not making any :?: Maybe a group buy I would get a couple more sets.


thatmight be the way to go, a group buy or maybe a Club purchase as these will always be a problem otherwise

_________________
'72 PR60 Sport


Thu Nov 07, 2013 5:33 am
Profile WWW

Joined: Wed May 19, 2010 10:35 am
Posts: 33
Car(s): Gt Bellett, Rover 90, Rover 75 ,327 hk Monaro, 307 ht Ute, Mazda 6 wagon.
Reply with quote
I have already checked with acl about getting them remade and they will do them but need to order a min of 300 sets very expensive I'll have a look through my spares as I should have a few spare sets that I won't need. Peter.


Thu Nov 07, 2013 7:37 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
gt 161 wrote:
I have already checked with acl about getting them remade and they will do them but need to order a min of 300 sets very expensive I'll have a look through my spares as I should have a few spare sets that I won't need. Peter.


Hi Peter,

do you know if they also fit SOHC and DOHC engines.

glenn

_________________
'72 PR60 Sport


Thu Nov 07, 2013 7:57 am
Profile WWW

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
The ones I have are nason 3c6127n made in Taiwan box says for g130/150/161/180/200 ? Maybe they might be of help :?:


Thu Nov 07, 2013 8:09 am
Profile

Joined: Wed May 19, 2010 10:35 am
Posts: 33
Car(s): Gt Bellett, Rover 90, Rover 75 ,327 hk Monaro, 307 ht Ute, Mazda 6 wagon.
Reply with quote
Hi Glen they will fit 1800 block as well


Thu Nov 07, 2013 8:31 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
gt 161 wrote:
Hi Glen they will fit 1800 block as well

thanks Peter.
(long time no see, mate)

glenn

_________________
'72 PR60 Sport


Thu Nov 07, 2013 9:08 pm
Profile WWW
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
gt orphanage wrote:
The ones I have are nason 3c6127n made in Taiwan box says for g130/150/161/180/200 ? Maybe they might be of help :?:


might be worth asking at Bursons etc........ thanks

glenn

_________________
'72 PR60 Sport


Thu Nov 07, 2013 9:12 pm
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 36 posts ]  Go to page Previous  1, 2

Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.