Here is the table of tightening torques for 5 bearing engines,
Cheers,
Lewis.
| Attachments: |
|
image.jpeg [ 391.98 KiB | Viewed 20484 times ] |
| bellett.net https://bellett.net/forums/ |
|
| Head Bolt Tension https://bellett.net/forums/viewtopic.php?f=36&t=3338 |
Page 1 of 1 |
| Author: | RobSA [ Sun Sep 18, 2016 9:24 am ] |
| Post subject: | Head Bolt Tension |
I've searched and cannot find it, so. What is the head bolt tension for the standard G150 in the Belletts? Cheers Rob |
|
| Author: | Asroc66 [ Sun Sep 18, 2016 12:14 pm ] |
| Post subject: | Re: Head Bolt Tension |
Hi Rob I think I recall standard is 7kgm = 50 ft lbs I go higher to about 9-10kgm = 68-72 ft lbs Depends on 'feel', Belletts have heapem big head bolts. Best to - clean out the thread with a tap - use Assembly lube on the thread and under the head Bolt (at a push could use engine oil but not quite as good) Cheers J |
|
| Author: | mrflibbles [ Mon Sep 19, 2016 3:06 am ] |
| Post subject: | Re: Head Bolt Tension |
yeah in the manual its 6-7 kgm Im pretty sure i did mine a bit tighter though. |
|
| Author: | RobSA [ Mon Sep 19, 2016 10:45 am ] |
| Post subject: | Re: Head Bolt Tension |
Thank you everyone for the info. Cheers Rob |
|
| Author: | RobSA [ Sun Jan 08, 2017 9:44 am ] |
| Post subject: | Re: Head Bolt Tension |
So does anyone have the correct tension for the rocker stand bolts ? |
|
| Author: | Teditor [ Sun Jan 08, 2017 10:51 am ] |
| Post subject: | Re: Head Bolt Tension |
I'm going back a long time, but the G150 has two head bolt sizes if I recall, 17mm for the 3 Bearing and 19mm for the 5 bearing, so I would assume two different settings, be careful about overtightening. Ted (Teditor) Freeman |
|
| Author: | 67GT [ Sun Jan 08, 2017 7:33 pm ] |
| Post subject: | Re: Head Bolt Tension |
Hi Rob, I do have that information, but it is at work. If I don't remember to post later, call meon 02 4393 2833 Warren. |
|
| Author: | Early GT [ Sun Jan 08, 2017 7:56 pm ] | ||
| Post subject: | Re: Head Bolt Tension | ||
Here is the table of tightening torques for 5 bearing engines, Cheers, Lewis.
|
|||
| Author: | RobSA [ Sun Jan 08, 2017 8:53 pm ] |
| Post subject: | Re: Head Bolt Tension |
Yippee. Thank you so much 
|
|
| Author: | 67GT [ Mon Jan 09, 2017 4:27 am ] |
| Post subject: | Re: Head Bolt Tension |
Lewis beet me to it. That is the same book I have. |
|
| Author: | RobSA [ Fri Jan 13, 2017 3:27 am ] |
| Post subject: | Re: Head Bolt Tension |
Tis good 67GT Wish it was easier to clean the head and block of the accumulated gunk. 40+ degrees then constant rain ... blah. Hard to get anything done at all. Head is nice and clean now. Next is to clean bolts and rocker gear, then if I can get some fine weather, the block. Cheers everyone
|
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|