bellett.net
https://bellett.net/forums/

DOHC head gasket changing.
https://bellett.net/forums/viewtopic.php?f=36&t=3524
Page 1 of 1

Author:  Feral_Kev [ Sat Dec 23, 2017 5:59 am ]
Post subject:  DOHC head gasket changing.

Hi there all.

I’m hoping that someone can help me out with changing the head gasket in the Red Beast.

I don’t have much in the way of funds or correct tools and knowledge to do this with the kids doing the work.

My back is buggered and can’t see the light at the end of the tunnel to work out if it’s truly light or knowing my luck a train.
I’m on the beautiful Central Coast NSW.
I have it in a garage to work on it.
Or I have a trailer to take it somewhere else to be done.

I won’t be putting it on the track any time soon but I hope to have it at some shows and display days but need it running.

If it was a push rod motor I could tell the kids how to do it in my sleep but I haven’t played with DOCH motors in a looong time.

ThankYou in advance. & Merry Christmas to all.

Cheers Kev.
0405290040.

Author:  PR91 [ Mon Dec 25, 2017 5:28 am ]
Post subject:  Re: DOHC head gasket changing.

Bring it to Melbourne and I'm happy to look after it for you.

Author:  Feral_Kev [ Tue Dec 26, 2017 12:03 pm ]
Post subject:  Re: DOHC head gasket changing.

Ohhh so tempting.
I wish I could handle a drive that far.

Anyone going south for the summer with a towball not in use.

Hmmm what to do and how to do it.

I will get back to you.

Cheers Kev.

Author:  Glenn [ Tue Dec 26, 2017 9:40 pm ]
Post subject:  Re: DOHC head gasket changing.

Feral_Kev wrote:
Ohhh so tempting.
I wish I could handle a drive that far.

Anyone going south for the summer with a towball not in use.

Hmmm what to do and how to do it.

I will get back to you.

Cheers Kev.


Antus is on here and did same job a while ago but no details . https://www.youtube.com/watch?v=54v-X4A1DsY

Author:  Feral_Kev [ Thu Dec 28, 2017 10:38 pm ]
Post subject:  Re: DOHC head gasket changing.

Howdy all.

I wish my body would let me fix this myself.

My back is extremely bad with 3 surgeries in the last year and a half with no luck.
I’ve had a heap of nerves burned off in my spine. No help.
So going to see about surgery number 4 in February.

I struggle to drive 30 mins without pain.

I sometimes struggle with pain lifting a 3litre milk bottle.

I’m hoping that someone can help me please.

Any one heading south with a towball not in use.

Cheers Kev.

Author:  67GT [ Fri Dec 29, 2017 10:26 pm ]
Post subject:  Re: DOHC head gasket changing.

Hi Ugly
I know a few mechanics in your area. Not Isuzu specific, but shouldn’t be too hard.

Author:  Farmer [ Sat Dec 30, 2017 10:44 pm ]
Post subject:  Re: DOHC head gasket changing.

Hey there Kev. Paying a mechanic may be the easiest solution, but never cheap anymore.
How hard can it be? I had to do a 3 litre Cressida twin cam and had no previous experience. Found a bunch of discussions online about the tension (which Toyota had too light in the first place, 52 ft/lb !!). It was a long job as there is lots of plumbing, but I took photos for the reassembly. I marked the timing chain and pulleys to get them back in the correct place, and didn't turn the motor while it was off. Took the head to Engine rebuilders in Canberra for a surface grind and hardness check. The valves and guides were all fine. (Only 150,000 ks)
You will need a tension wrench, but standard sockets and tools should do the rest. I had to borrow a high tensile hex drive for the tension wrench as it had hex studs.

I reckon with you pointing and directing, the young ones can do it.
Good luck!

I hope the next surgery is the last you need, and you become pain free. I have had a herniated disc in the past, which still gives me grief sometimes, but I've learned to be careful. Back pain is the worst, but if you can still get around, thats better than for some. You will be better in the future.
Cheers and happy new year,
Matt.

Author:  gricey [ Mon Jan 01, 2018 6:37 am ]
Post subject:  Re: DOHC head gasket changing.

can!t be to hard if i can do it.gricey

Author:  Feral_Kev [ Mon Jan 08, 2018 1:50 am ]
Post subject:  Re: DOHC head gasket changing.

Thanks All.

Going to put if off sadly for a couple of months now.

It’s just going to be a show pony trailer queen.
Let’s hope if it goes somewhere It doesn’t have to be pushed too far from the trailer.

Cheers Kev.

Author:  Stickman [ Sun Jan 14, 2018 1:03 am ]
Post subject:  Re: DOHC head gasket changing.

BUGGER! If I had internet service in the lead up to the holiday break I might have seen this and could have trailered it anywhere south for you.
I had an empty flat bed and car trailer all the way from Brissy to Albury to pick up a couple of cars myself (inc the Wagga sedan off Ebay)
Only gear I had on board for the south bound trip was the bigger parts for Peter's 117 that he couldn't get sent with the car.


Not good to hear about your back mate
Hope the 4th attempt gives you some relief from the pain

Author:  Feral_Kev [ Wed Jan 24, 2018 9:07 am ]
Post subject:  Re: DOHC head gasket changing.

Howdy all

I’m not too sure how long it’s going to take but it looks like a bolt or 2 a day to strip it down.

Then check what needs fixing. I’m pretty sure my budget is like the process about $1 a day.

If people get bored with their lives and want a working holiday on the beautiful central coast I’m sure you can get as busy as you like.
Just remember the budget $1 a day.

Cheers Kev.

Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/