bellett.net

If only mine was that close. But. Not too far away.

Dave.

Sorry. No pics yet. Have lots of. Working on that 2.

Hi Peter.
82300086 will suit G150C and G160 engines up to 1966.
82300093 will suit G150C-1. 1967. The difference between these 2 distributors is the cam, balance weight (governor) springs and the
vacuum advance. Isuzu lists a dizzy for the G161 late '68.
I haven't any records of the 5.81300016.0 ...

BP6ES plug. B= 14.0mm thread. P= Projecting insulator type. 6= Heat range. E= 19.0mm Thread length. S= Standard type.
BCP6ES plug. BC= 14.0mm thread with copper core electrode. The rest of the part number is identical to above.
BPR6ES plug. BP. As above in description. R= Resistor type. The rest is ...

Of all the logos, emblems and symbols that I have on Isuzu. I have not seen that one.
All possibility that your European contact is correct.
Dave.

I'm not going. Clashes with my hockey commitments.
Dave.

Florian Finder at it again. Good onya Matt. Super Sleuth.
Going by the dust been sitting awhile. Left front door has been opened a little tooo far.
Early Wibroc spring loaded mirror for bird strikes, or someone walks a little bit closer than they should.
At least 1 genuine wheel cover. Unable to ...

Clarification on my previous post. Thought it was getting pretty close to a novel.
The difference between a sedan and a GT harness.
The GT has a amp meter and the wire has a terminal joint in it to access the meter. The sedan doesn't have
this joint but I estimate that you may be able to adapt to ...

Hi Earthp. I have a few questions in regards to your request.
Have you got the old harness for your vehicle.?.
If you have. Is it "burnt out" or damaged in a way that you may not be able to salvage it.?.
Are you able to access a sedan harness.?.
Have you got a sedan and a GT wiring harness diagram ...

Thanks for the pics Peter. Good to follow a resto.
Your paint work has given me inspiration in what I should do for my resto.
Will make a final decision on the side stripes when the time comes.
Most of my time has been knocking 2 big dents out of the roof.
Has been too cold to paint at the moment ...

GBP 8,999.00 exchange to $AU is $15,721.00. As at 09 07 2022.
With the photos that are presented I'm not able to see the familiar rust spots in a Series 3 (strip tail lamp).
Although it has had a flick of paint in some areas. The boot area is an example. Rubber grommet and wiring harness boot
not ...

Thank you julieandtom. I have had calipers at my brake specialist for quiet some time. All 4 pistons were shot.
He was concerned that the locating pin in the centre of the piston was necessary and finding a piston with a pin
and diameter required would be hard to get.
I assured him that a piston ...

Sometime back at one of the nationals there was an attendee who had some samples of covers that
he had spun up. If anybody was interested he would be able to take orders.
Can anybody recall who that person was.??

Dave.

Ready to go in. Piazza shift extension.
I shifted the handbrake rearwards and manufactured a false tunnel similar to the wasp.

Dave.

Hi Clyde.
Attached pics.

Enjoy.

Dave.

Cutting the 5 speed transmission housing away is what I had done to fit the standard starter to my sedan. The housing shown
is probably out of a KB Rodeo or a UBS Jackaroo Diesel (left hand starter) with a what we called in the auto parts industry
a "dropped down starter drive". I manufactured a ...

Hi Glenn.
Your correct. Both bores are 3/4". 19.05mm.
The secondary cup on the single master cylinder is the same cup on the secondary piston on the twin.
The secondary piston is the piston at the back of the cylinder and operates the front brakes.
All the other cups are different part numbers. Did ...

Hi Emma and Ross.
Half expected that the Nationals would not be going ahead as planned. Reducing the amount of sections of entertainment to to accommodate the South Australian people and those who wish to take the chance and go. Joe and I don't want to risk it. Crossing the borders and not knowing ...

Parts listing for heaters. As you can see the difference between the early duct hose and the late.

Dave.

I was wondering if the South Australia importer had GT's come in without the factory heater and fitted an accessory type just to keep costs down.
The heat exchanger is the same as my white GT and it's from South Australia. I mentioned before in this post that my first
car I fitted a Smiths' heater ...

Re-confirmed accommodation booking for 2 persons. Staying Thursday night to Sunday night.
All I have to do now is finish a car.

Dave.