View unanswered posts | View active topics It is currently Thu Mar 28, 2024 9:31 pm



Reply to topic  [ 17 posts ] 
GT Parts needed 
Author Message

Joined: Sun Mar 07, 2010 8:06 am
Posts: 210
Car(s): PR90, PR91, Teardrop Bellett Sedan, 1979 Pontiac Trans Am Firebird, 1975 HJ Belmont Ute,Yamaha YB100
Reply with quote
Am starting my GT resto so just putting it out there if anyone is willing to part with any of the following, let me know......after you get back up off the floor

Tacho
1600 head gasket
extractors
exhaust gasket

Thanks
Craig


Wed May 30, 2012 6:26 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
might be a tough ask for some of those parts.

Jason has a few Bellett parts in another thread in Japanese auctions. Keep an eye on that, some of the bits might turn up.

I think i have a s/h exhaust gasket somewhere.

The BCCV used to have Gasket kits but i think none left although possibly that might change if they find/get made some more..

_________________
'72 PR60 Sport


Wed May 30, 2012 6:52 am
Profile WWW

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
head gasket repco part no is cj151 acl brand it is a valve regrind set with tappet cover gasket ect for a luv. manifold gasket is not going to work.
I have manifold gaskets made they are $40 each i am out at he moment but another ten are being made.
extractors are on the go too i have a luv 1 made for the race car and the gt gasket and manifold are going down next to lazer cut the plates soon. i only got a call yesterday to say the luv plate is done.


Wed May 30, 2012 8:07 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
my enquires down here for that set have shown no stock. Only the valve seals are still available.

glenn

_________________
'72 PR60 Sport


Wed May 30, 2012 9:21 am
Profile WWW

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
We got a few sets a couple of weeks back, let me know if you have no luck we have a contact at acl ;).


Wed May 30, 2012 9:46 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
Don't need one but was there getting other stuff so thought i would ask

BCCV though should get a few

glenn

_________________
'72 PR60 Sport


Wed May 30, 2012 9:53 am
Profile WWW

Joined: Mon Jan 10, 2011 1:03 pm
Posts: 2419
Car(s): 1966 TEARDROP ...MANUAL ...
Reply with quote
mate how did you lose the tacho or did it die ? have seen them come up on the o/s look what we have market place cheers davo


Wed May 30, 2012 9:55 am
Profile

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
If it's only dead otto instruments put a new guts in them past experience is they are wired wrong you have to swap the two wires around the tacho overides the points a she no go :o .


Wed May 30, 2012 10:00 am
Profile

Joined: Mon Jan 05, 2009 10:39 am
Posts: 1136
Location: Adelaide Hills
Car(s): GU Patrol, AU ute, 1969 florian deluxe, 1976 Luv & 1980 KB 4x4 isuzu
Reply with quote
is the 1500 head gasket the same as the 1600?

_________________
I am "that" Florian guy.
never buy a car you cant push.


Wed May 30, 2012 10:06 am
Profile

Joined: Fri Mar 20, 2009 8:23 am
Posts: 1816
Reply with quote
they would be in the bore size but i use them on 1500,s


Wed May 30, 2012 10:09 am
Profile

Joined: Sun Mar 07, 2010 8:06 am
Posts: 210
Car(s): PR90, PR91, Teardrop Bellett Sedan, 1979 Pontiac Trans Am Firebird, 1975 HJ Belmont Ute,Yamaha YB100
Reply with quote
Car didnt come with tacho or extractors, Was sitting on a farm for about 7-8 years. Had back windsceen smashed by vandals. tacho was either stolen or was placed by owner in one of his 6 or 7 sheds, unlikely to ever be found again in my lifetime. Likely there will be other parts missing as I progress but these are the most obvious peices at the moment.


Wed May 30, 2012 11:06 am
Profile

Joined: Tue Mar 24, 2009 11:52 am
Posts: 843
Location: Sunshine Coast QLD
Car(s): PR95 PR20 WASP SWB NH Pajero Superchrged NT Pajero BF SR6 Falcon
Reply with quote
I have a tacho from a 117, the same as GT. don't know what condition it is in, if you are interested pm me

Geoff


Wed May 30, 2012 12:22 pm
Profile

Joined: Tue Sep 16, 2008 11:54 am
Posts: 2542
Reply with quote
had to make a set of extractors a few years ago for mine.
originals are over 40 years old now, and 90% are stuffed. my originals were waffer thin, and was a never ending job to patch them up, so i made a brand new set instead.
should be ok for another 40 years.


Fri Jun 01, 2012 11:08 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
did ypou make yourself Brett or get them made ?

glenn

_________________
'72 PR60 Sport


Fri Jun 01, 2012 11:13 am
Profile WWW

Joined: Tue Sep 16, 2008 11:54 am
Posts: 2542
Reply with quote
me Glenn. but did it in a mates exhaust shop when he still had it.
used the original mounting plate, but all new pipes and now a flat, bolt on flange to the exhaust, not a slip joint.
not that hard to do, and i'd still do my own even tho he doesn't have the shop anymore, but with bends and straight pipe sections u can buy separately, because a good exhaust shop with A: someone who cares, and B: someone who actually knows how to do custom work as opposed to "bolt off, bolt on" is getting bloody hard.
there are some around that do very nice work, but they know how to charge too....
mind u, my standards of what i'll except as a good job is probably higher than some, so i can be critical sometimes.


Fri Jun 01, 2012 11:26 am
Profile
User avatar

Joined: Tue May 10, 2011 2:23 am
Posts: 2816
Location: Melb.
Car(s): '72 Sport Bellett (imported 180912), M/B AMG A35, i30, had Belletts in past, 2 sed, 3 GT's.
Reply with quote
yes, i have done one myself using U bends when i had the 1600 DOHC toyota motor in the white GT. Tedious but easy enough to do.
Not much choice though, toyota in a bellett, no off the shelf stuff LOL

glenn

_________________
'72 PR60 Sport


Fri Jun 01, 2012 11:35 am
Profile WWW

Joined: Tue Sep 16, 2008 11:54 am
Posts: 2542
Reply with quote
bellett in a bellett (ie: original) and there no off the shelf stuff either...
:lol:


Fri Jun 01, 2012 11:02 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 17 posts ] 

Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.