Bellett 4:11 diff gears

Please be specific as to what part you're after - unless you're after a whole car for parts!
Post Reply
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

haha no i dont think you would have all reverse gears as im pretty sure with a 4x4 the tailshaft going into the diff spins the opposite way to the rear tailshaft.
Top
User avatar
KJB
Posts: 619
Joined: Fri Nov 07, 2008 9:05 am
Car(s): Bellett GT, Bellett Sedan, Prince Skyline GT, Porsche tractor, Lanz Bulldog, 996 Carrera 4,Prince Miler,
Location: Western Victoria

Re: Bellett 4:11 diff gears

Post by KJB »

Or turn the diff. centre over.
KB
Around here the Laws of Physics and Reality are strictly enforced !
Top
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

how much do you want for your front diff posted to qld? ill pull it apart and see if it fits...i doubt it but...if not ill stick to the 4:11 florian center
Top
User avatar
OzLuvTrucker
Posts: 139
Joined: Tue Mar 10, 2009 11:10 am
Car(s): 1980KBD40 ISUZU

Re: Bellett 4:11 diff gears

Post by OzLuvTrucker »

If the above ? is for me i can pull a center apart and take measurements.
Top
User avatar
OzLuvTrucker
Posts: 139
Joined: Tue Mar 10, 2009 11:10 am
Car(s): 1980KBD40 ISUZU

Re: Bellett 4:11 diff gears

Post by OzLuvTrucker »

Right click to open larger pics in new tab.
Image
Image
Image
Image
Image
Image
Image
Image
Last edited by OzLuvTrucker on Tue Sep 25, 2012 11:04 am, edited 1 time in total.
Top
User avatar
OzLuvTrucker
Posts: 139
Joined: Tue Mar 10, 2009 11:10 am
Car(s): 1980KBD40 ISUZU

Re: Bellett 4:11 diff gears

Post by OzLuvTrucker »

Pinion bearings - smaller bearing 30305c larger bearing 02420
Crown bearings LM4851c-cup LM48548a-cone
22t spline count 41 teeth on crown 9 on pinion = 4.56
Top
BULLITT
Posts: 2419
Joined: Mon Jan 10, 2011 1:03 pm
Car(s): 1966 TEARDROP ...MANUAL ...

Re: Bellett 4:11 diff gears

Post by BULLITT »

ozluvtrucker ..love your postings its good when you can ask the auricles when you have tricky questions ..again this is why the forum works cheers davo great shots of the diff ...
Top
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

wow awesome pics mate damn looks so similar ill have to go up in the shed and take a look at the pinion gear tomorrrow and let you know! but looking at it right now it looks damn much the same!
Top
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

just checked and the pinion gear is slightly differant...it has like a differant bearing holder
Top
User avatar
OzLuvTrucker
Posts: 139
Joined: Tue Mar 10, 2009 11:10 am
Car(s): 1980KBD40 ISUZU

Re: Bellett 4:11 diff gears

Post by OzLuvTrucker »

Bugger :|
Top
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

hang on a minute! my bellett crown wheel look the same the bellett has 41 teeth the only thing is the pinion gear..but when i looked at mine the bearing runner is pressed on so its not part of the pinion shaft itself..can you measure exactly how long the pinion gear is and also the thickness of the shaft were the bearing sits. the spline is differant but i can use the spline that you have in your picture..can you measure the diamtere of the crown wheel also...need precise measurement...but it might be a case of a tiny bit of machining and it will work!!
Top
User avatar
Waldo
Posts: 194
Joined: Tue Oct 21, 2008 7:12 am
Car(s): 1968 Bellett GT
Location: Brisbane

Re: Bellett 4:11 diff gears

Post by Waldo »

just comparing the pics it looks like a goer!! just need to use the front spline part that the tailshaft bolts too!
Top
Post Reply

Return to “Wanted!”